Technical Datasheet
Fast Setting Wood Glue - LIONGRIP X-TRA
Product # R7600430
Fast-Setting PVA Adhesive
The LIONGRIP X-TRA is a polyvinyl acetate based adhesive characterized by high solids content and rapid setting. It can be used for bonding a wide variety of wood species (except exotic wood) in applications such as composite board, edgebanding and surface bonding. The dry film is easily sanded and is not affected by lacquers, paints, or varnishes. Contains a UV tracer for easier viewing with ultraviolet blacklight for removal of excess adhesive.
ADVANTAGES AND BENEFITS
- Low assembly and press time
- High solids
- Strong bond
- Dries clear
- UV tracer
- Easily sanded
- Unaffected by lacquers, paints and varnishes
- Contains no added urea-formaldehyde resin
- Easy clean-up
- High solids
- Strong bond
- Dries clear
- UV tracer
- Easily sanded
- Unaffected by lacquers, paints and varnishes
- Contains no added urea-formaldehyde resin
- Easy clean-up
TECHNICAL SPECIFICATIONS
Product #
R7600430
Recommended Use
Interior, Edgebanding, Cabinet, Particleboard, Masonry, Wood, Veneer, Furniture Renovation
Color Before Application
White
Dried Film
Clear
Open Time
5 to 7 minutes
Close assembly time under pressure
5 to 7 minutes
Viscosity
3 500 - 4 500 cps
Brand
Liongrip
Features
Fast-Drying, Fluorescent, Low VOC (less than 250 g/l), Heavy-Duty, Superior Bond, Wash with Water
VOC Concentration (EPA Method 24)
< 30 grams/Liter
Standards and Certifications
LEED
Recommended Coverage
22,30 m²/3,78 l (240 sq ft/gal)
Solid Content (Approx.)
56% - 60%
Base
Polyvinyl Acetate
Freeze/Thaw Stability
Keep From Freezing
APPLICATION
Preparation
- Mix well before using. Adhesive.
- Material and room temperature should be above 10°C/50°F.
- All surfaces to be glued must be clean and dry.
- Best bonds are obtained when moisture content of wood is between 8% and 12%.
Application
- Apply directly from the plastic bottle or with a brush or a glue spreader. Joints must be tight fitting.
- Spread glue to result in squeeze-out when parts are assembled.
- Clamp or press using sufficient pressure. When glue becomes translucent, a full strength bond has formed.
- Allow to dry before sanding.
Guidelines (AT 20°C & 50% RH)
Assembly time: 5 to 7 minutes
Clamp time: 15 to 20 minutes
Drying time: 4 to 6 hours
Spread rate: approx. 6 sq. m./L (240 sq. ft/ gallon)
- Mix well before using. Adhesive.
- Material and room temperature should be above 10°C/50°F.
- All surfaces to be glued must be clean and dry.
- Best bonds are obtained when moisture content of wood is between 8% and 12%.
Application
- Apply directly from the plastic bottle or with a brush or a glue spreader. Joints must be tight fitting.
- Spread glue to result in squeeze-out when parts are assembled.
- Clamp or press using sufficient pressure. When glue becomes translucent, a full strength bond has formed.
- Allow to dry before sanding.
Guidelines (AT 20°C & 50% RH)
Assembly time: 5 to 7 minutes
Clamp time: 15 to 20 minutes
Drying time: 4 to 6 hours
Spread rate: approx. 6 sq. m./L (240 sq. ft/ gallon)
IMPORTANT INFORMATION
- Shelf life is 18 months at room temperature in original unopened container
- Store indoor in a cool, dry location between 10°C/50°F and 35°C/95°F
- Keep container closed when not in use and protect from freezing
- Store indoor in a cool, dry location between 10°C/50°F and 35°C/95°F
- Keep container closed when not in use and protect from freezing
DISCLAIMER
Our personnel is available to help purchasers obtain best results from our products, and recommendations are based on tests and information believed to be reliable. However, since we have no control over the conditions under which our products are transported, stored, handled, or used by purchasers, all recommendations and sales are made on condition that we will not be held liable for any damages resulting from their use. No representative of ours has any authority to waive or change this provision.
