New

Water Resistant Press Glue - LIONGRIP VERSA II

To buy, choose from the options below.
Volume: 135 oz* 31.7 pt* Select Options
Product № Volume
R7200130 135 oz*
R7200430 31.7 pt*

Description

Type II PVA Adhesive

The LIONGRIP VERSA II is a precatalized crosslinkable polyvinyl acetate based adhesive that provides good water-resistance and excellent bond strength. The VERSA II meets ANSI Type II water-resistance which makes it suitable for end products that are intended to be exposed to weather, and for interior projects where high humidity resistance or water resistance is beneficial.

ADVANTAGES AND BENEFITS

- Water-resistance: PVA Type II
- One-part glue
- Easy clean up
- Can be cold pressed, hot pressed or radio frequency cured
- Contains no added urea-formaldehyde resin
- The use of this product may contribute to obtaining LEED credits
- Product certified for reduced environmental impact (ECOLOGO UL2762)

TECHNICAL SPECIFICATIONS

Recommended Use
Interior, Cold-Pressed Glue, Particleboard, Masonry, Wood, Laminates, Veneer, Hot Pressing, Radio Frequency Pressing, Flooring
Color Before Application
White
Dried Film
Clear
Open Time
10 to 12 minutes
Close assembly time under pressure
15 to 20 minutes
Viscosity
4000 - 5500 cps
Brand
Liongrip
Features
Low VOC (less than 250 g/l), Water Resistant, Superior Bond, Wash with Water
VOC Concentration (EPA Method 24)
< 30 grams/Liter
Standards and Certifications
LEED, UL2762, CSA 0112.8 M1977 / Type II, DIN 68602 B3, CSA 0132.2.3 Type I, NWWDA I.S.1 Type I, BS EN 2004 : 1991 / Class D3
Recommended Coverage
22,30 m²/3,78 l (240 sq ft/gal)
Solid Content (Approx.)
48% to 50%
Base
Polyvinyl Acetate
Freeze/Thaw Stability
Keep From Freezing
Disclaimer

Measures shown with an asterisk (*) have been converted as per your preference. These are not the official measures. To view the measures specified by the manufacturer, click here.

APPLICATION

Preparation

- Mix well before using. Adhesive.
- Material and room temperature should be above 20°C/68°F.
- All surfaces to be glued must be clean and dry.
- Best bonds are obtained when moisture content of wood is between 8% and 12%.


Application

- Apply directly from the plastic bottle or using a stiff brush or a mechanical glue spreader. Joints must be tight fitting.
- Spread glue to result in squeeze out when parts are assembled.
- Clamp or press using sufficient pressure. When glue becomes colorless, a full-strength bond has formed.
- Allow to dry before sanding.


Guidelines (AT 20°C & 50% RH)

Assembly time: 15 to 20 minutes
Clamp time: 25 to 60 minutes
Drying time: 6 to 8 hours
Spread rate: approx. 6 sq. m./L (240 sq. ft/ gallon)

IMPORTANT INFORMATION

- Not for continuous submersion or use below waterline
- Must dry 5 hours before being exposed to water or humidity
- Shelf life is 18 months at room temperature in original unopened container
- Store indoor in a cool, dry location between 10°C/50°F and 35°C/95°F
- Keep container closed when not in use and protect from freezing

DISCLAIMER

Our personnel is available to help purchasers obtain best results from our products, and recommendations are based on tests and information believed to be reliable. However, since we have no control over the conditions under which our products are transported, stored, handled, or used by purchasers, all recommendations and sales are made on condition that we will not be held liable for any damages resulting from their use. No representative of ours has any authority to waive or change this provision.
Water Resistant Press Glue - LIONGRIP VERSA II
Water Resistant Press Glue - LIONGRIP VERSA II
To buy, choose from the options.